SC16IS752/SC16IS762

General description

The SC16IS752/SC16IS762 is an I²C-bus/SPI bus interface to a dual-channel high performance UART offering data rates up to 5 Mbit/s, low operating and sleeping current; it also provides the application with 8 additional programmable I/O pins. The device comes in very small HVQFN32 and TSSOP28 packages, which makes it ideally suitable for hand-held, battery-operated applications. This chip enables seamless protocol conversion from I²C-bus/SPI to RS-232/RS-485 and is fully bidirectional.

The SC16IS762 differs from the SC16IS752 in that it supports SPI clock speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the SC16IS752, and in that it supports IrDA SIR up to 1.152 Mbit/s. In all other aspects, the SC16IS762 is functionally and electrically the same as the SC16IS752.

The SC16IS752/SC16IS762's internal register set is backward compatible with the widely used and widely popular 16C450. This allows the software to be easily written or ported from another platform.

The SC16IS752/SC16IS762 also provides additional advanced features such as auto hardware and software flow control, automatic RS-485 support and software reset. This allows the software to reset the UART at any moment, independent of the hardware reset signal.

Features

General features

• Dual full-duplex UART
• I²C-bus or SPI interface selectable
• 3.3 V or 2.5 V operation
• Industrial temperature range: -40 Cel to +95 Cel
• 64 bytes FIFO (transmitter and receiver)
• Fully compatible with industrial standard 16C450 and equivalent
• Baud rates up to 5 Mbit/s in 16x clock mode
• Auto hardware flow control using RTS/CTS
• Auto software flow control with programmable Xon/Xoff characters
• Single or double Xon/Xoff characters
• Automatic RS-485 support (automatic slave address detection)
• Up to eight programmable I/O pins
• RS-485 driver direction control via RTS signal
• RS-485 driver direction control inversion
• Built-in IrDA encoder and decoder supporting IrDA SIR with speeds up to 115.2 kbit/s
• SC16IS762 supports IrDA SIR with speeds up to 1.152 Mbit/s¹
• Software reset
• Transmitter and receiver can be enabled/disabled independent of each other
• Receive and Transmit FIFO levels
• Programmable special character detection
• Fully programmable character formatting
  • 5-bit, 6-bit, 7-bit or 8-bit character
  • Even, odd, or no parity
  • 1, 1 1/2, or 2 stop bits
• Line break generation and detection
• Internal Loopback mode
• Sleep current less than 30 uA at 3.3 V
• Industrial and commercial temperature ranges
• 5 V tolerant inputs
• Available in HVQFN32 and TSSOP28 packages

I²C-bus features

• Noise filter on SCL/SDA inputs
• 400 kbit/s (maximum)
• Compliant with I²C-bus Fast mode
• Slave mode only

SPI features

• SC16IS752 supports 4 Mbit/s maximum SPI clock speed
• SC16IS762 supports 15 Mbit/s maximum SPI clock speed
• Slave mode only
• SPI Mode 0

1. Please note that IrDA SIR at 1.152 Mbit/s is not compatible with IrDA MIR at that speed. Please refer to application notes for usage of IrDA SIR at 1.152 Mbit/s.

Products/packages

Pricing/ordering/availability

Applications

• Factory automation and process control
• Portable and battery operated devices
• Cellular data devices

Block diagrams/pinning

Technical documents

Application Notes

AN10417_1; SC16IS760/762 Fast IrDA mode (08-Jun-06)

AN10428_1; UART-SPI Gateway for Philips SPI slave bridges (06-Mar-06)

AN10462_1; SPI programming for Philips Bridge ICs (01-Jun-06)

AN10485_1; SDA pin connection in SPI mode (02-Jun-06)

AN10486_1; Automatic RS-485 address detection (02-Jun-06)

AN10571_1; Sleep programming for NXP bridge ICs (08-Jan-07)

AN10587_1; Interfacing NXP bridge IC with NXP ARM microcontroller (26-Feb-07)

Support Documents

75016189; NXP I (2008-06-01)

web; NXP SC16IS7xx I2C/SPI-to-UART demo board kits ()

75015676; NXP low-power bridges SC16IS750/52/60/62 (2006-09-01)

75014352; new multimarket products (2005-11-04)

Print / Email

• Print this information
• Email this information

Disclaimer

The information published on product information pages of the www.nxp.com or www.semiconductors.com websites is an extract from product data sheets and is for information purposes only. For detailed information please check the most recent version of the relevant product data sheet as published on these websites. In the event of any conflict between product information pages and data sheets or deviations from information provided in the product data sheets on these product information pages, the information provided in the product data sheets shall prevail.

The product status of the product(s) described in the product data sheet may have changed since publication of the data sheet and therefore information in datasheets on product status may be outdated. The latest information on product status is published on the product information pages of the above-mentioned websites.

As from October 1st, 2006 Philips Semiconductors has a new trade name - NXP Semiconductors, which will be used in future data sheets together with new contact details. In data sheets where the previous Philips references remain, please use the new links as shown below.

http://www.philips.semiconductors.com use http://www.nxp.com

http://www.semiconductors.philips.com use http://www.nxp.com (Internet)

sales.addresses@www.semiconductors.philips.com use salesaddresses@nxp.com (e-mail)

The copyright notice at the bottom of each page (or elsewhere in the document, depending on the version)
- © Koninklijke Philips Electronics N.V. (year). All rights reserved -
is replaced with:
- © NXP B.V. (year). All rights reserved.-

If you have any questions related to the data sheet, please contact our nearest sales office via e-mail or phone (details via salesaddresses@nxp.com). Thank you for your cooperation and understanding.